Top 10 common forklift crashes ， forklift procedure need to take notice of these matters ！.

Top 10 common forklift crashes ， forklift procedure need to take notice of these matters ！.

Blog Article

Do not underestimate the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift freight obstructed the motorist's view, and the individual ahead might not be discovered, leading to a rolling mishap.
Situation 2: In order to maintain the balance of the forklift when lifting hefty items, the staff members utilized their body weight as the weight, which nearly created casualties.
Situation 3: The width of the forklift cargo exceeds the allowable width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift raises the personnel illegally, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Prior to starting, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the task website or while driving, be careful that there will be no challenges overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to shut off the fire and slide, and it is restricted to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the factory and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the tons need to not obstruct the motorist's sight. In special circumstances, when the item affects the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory location is 5 km/h, and it needs to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a prompt fashion, and they will never run with diseases or conceal them.

filling and dumping.
1. When fork-loading products, the distance in between the two forks need to be readjusted as needed to make the lots of the two forks balanced and not manipulated, and one side of the item need to be against the rack. .
2. It is restricted to work with a solitary fork or utilize a fork top or pull. In unique situations, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and constant. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it should be noted that the fork pointer ought to not touch various other goods or items. The Stand-on Electric Pallet Stacker lots ought to be supported with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted forward somewhat when the lots is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at broadband and ram hard objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining is restricted, and it is forbidden to make use of forks to raise employees to engage in high-altitude operations to prevent high-altitude dropping mishaps. .
9. It is not permitted to make use of the brake inertia to slide, put, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is shut off and the power is removed. (Except for special scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no turning on the slope is permitted.
7. Do not drive across the slope. When the gradient is greater than 10%, the automobile ought to be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy products and go to the motorist's line of sight, they must take the reversing workout
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal Electric Forklift Truck for Warehouse slope above 5%.
3. When there is an barrier on one side of the road, the opposite side of the section with the exact same length as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844